- Usb To Parallel Cable Drivers
- Parallel To Usb Adapter Driver
- Usb To Parallel Adapter Driver Windows Xp
The ICUSB1284 6 ft USB to Parallel Printer Adapter - M/M allows USB capable PCs to print to any standard parallel printer, converting a USB port into a Centronics (male) connector for direct connection to a parallel printer.
Active6 years, 9 months ago
Possible Duplicate:
How do I simulate a parallel (LPT) Printer with a USB Printer?
How do I simulate a parallel (LPT) Printer with a USB Printer?
I have a legacy DOS application that needs to print to a LPT port and only have USB ports on the host machine. I have installed a usb to parallel adapter to connect the printer. The adapter installed correctly with the USB Printer Support driver, however the adapter does not appear as a LPT port.
How do I assign a LPT port to the usb adapter?
Community♦
HendréHendré29333 gold badges66 silver badges1212 bronze badges
marked as duplicate by Dave, CharlieRB, Gaff, RedGrittyBrick, KaranJan 2 '13 at 17:44
This question has been asked before and already has an answer. If those answers do not fully address your question, please ask a new question.
Usb To Parallel Cable Drivers
1 Answer
Use the following steps:
- Do a 'right mouse' click on your printers name
- Choose 'Properties' from the popup menu
- Click on the 'Ports' tab at the top
- Write down the name of your USB port name
- Click on the 'Enable Printer Pooling' checkbox
- Scroll through all of your listed ports and click on 'LPT1' port.
- Click on 'Apply' and 'Ok'.
1,94444 gold badges2222 silver badges4545 bronze badges
Not the answer you're looking for? Browse other questions tagged windows-7usbprinterms-dosparallel-port or ask your own question.
PL2305 USB to Printer Bridge Controller driver is added below which will take you to the download page as this chipset is from Prolific. This chipset you will find in the USB-C to Parallel Printer Cable adapters. This cable is a bi-directional bridge between the Universal Serial Bus (USB) system and IEEE-1284 parallel port printers.
PL2305 USB-C to Parallel Printer Driver
The drivers for this should be in your Windows driver files and is a standard driver in Windows. You can also find the drivers for the StarTech 2 Port USB to RS232 Serial DB9 Adapter as well as the Cisco USB Console Cable – USB to RJ45. This cable allows you to USB to save the expense of replacing your serial printer as the DB25 adapter saves you the cost of replacing a parallel printer for a USB compatibility printer. Note that they all use the Prolific USB to serial driver.
Bus Type | USB-C |
Chipset ID | Prolific – PL2305 |
Interface | Parallel |
Ports | 1 |
Maximum Data Transfer Rate | 1.5Mbps |
System and Cable Requirements | One available USB-C port |
Connector Type(s) | 1 – USB Type-C (24-pin) USB 2.0 (480Mbps) Male |
1 – DB-25 (25 pin, D-Sub) Female | |
Power Source | USB-Powered |
Note the driver for the adapter is found below. Hirens boot usb windows 10.
This will open to the installation pages.
Parallel To Usb Adapter Driver
USB to Serial Driver (Windows)
FT232r USB UART Driver (Linux)
VN:F [1.9.22_1171]
VN:F [1.9.22_1171]
PL2305 USB-C to Parallel Printer Driver, 10.0 out of 10 based on 1 rating Incoming Search Terms:
Related Posts
Usb To Parallel Adapter Driver Windows Xp
- Prolific USB to Serial Driver (1.000)
- Gigaware USB to Serial Driver (1.000)
- Aten USB to Serial Driver (1.000)
- Bafo USB to Serial Driver (1.000)
- Prolific USB to Serial Comm Port Driver (1.000)